Nanit Local View Only (What Does It Mean and How to Fix It)

Using the Nanit baby monitor in my house, I’ve observed that the app says “local view only” approximately once a week or so.

Despite the fact that the video stream and loudness remained unaffected, I contacted Nanit immediately since I had no understanding what the warning signified.

How to fix Nanit’s local view only?

The only way to know if your Internet is down is if your Nanit baby monitor stays in local view only. After unplugging and re-plugging your router for 60 seconds, the problem should be solved This should reconnect your Internet connection and bring you out of the local view again. 

After hearing the news, your initial response is likely to be “Huh?” My WiFi isn’t working if my Internet isn’t.

No, the WiFi and Internet are not the same. I know, it’s mind-boggling. In a second, I’ll explain.

But first, let me make things clear.

If you don’t have Internet connection, your Nanit baby monitor will operate, but it still requires electricity and a WiFi signal.

Your Nanit must first be set up with a working internet connection, and only then can WiFi be used (in the event that you lose Internet access in the future).

As a result, the camera must be linked to the same WiFi network that was used when it was first set up.

A new WiFi network would need a re-installation of your Nanit, which would necessitate access to the Internet.

WiFi vs the Internet

When your phone has a good WiFi connection, but you can’t connect to the Internet – it’s probably something you’ve run into before.

See also  How to Make Alexa Stop Saying “OK” (Quick and Easy!)

To understand why “local view only” keeps appearing up in your Nanit app, you need to know that they are two separate things.

You may link your smart phone, computer, etc. wirelessly using WiFi technology (Local Area Network).

Think of WiFi as a substitute for the wire that people used to require to connect to their router.

There are hundreds of millions of smaller networks that are linked to the Internet, which is the term given to these networks.

As we’ll see later, there are a lot of reasons why the Internet and your Local Network may get disconnected from one other.

It’s possible to have a strong WiFi signal and an active connection to your router (for your Local Network!) while not being connected to the Internet, such as with your Nanit and smartphone.

When this occurs, you may still use your router to run your Nanit software (Local Network).

If you have power and WiFi, you can continue use your Nanit even if the Internet goes down. This is a nice feature to have.”

Here’s what you need to do to get your Internet back up.

Because our Internet service has been terminated, but our WiFi service has not, our Nanit displays “local view only.”

We need to get the Internet back up and running in order to repair this.

For most people, unplugging and re-plugging their router/modem is the quickest and most effective approach to re-establish their Internet connection.

After reconnecting your router, disconnect your Nanit monitor and keep it unplugged for 60 seconds before replugging it.

This will get the majority of individuals back online and out of their Nanit’s local vision.

See also  Blink Camera Not Working (Here Are 5 Fixes to Common Issues!)

Otherwise, I would suggest doing a factory reset on your router to see if it fixes the problem. Press and hold the reset button on your router for 15 seconds to perform a factory reset.

Your router will be reset to its original factory settings when you use this method. Please be aware that if you do this, you’ll have to rename and reset your Internet connection.

If you’ve tried disconnecting and hard resetting your router/modem but are still experiencing Internet problems, it’s possible that the network of your Internet service provider is down.

Call your Internet service provider to see if they can assist you in troubleshooting further.

Connection loss is caused by a variety of factors.

Your Local Area Network may lose its connection to the Internet for a variety of reasons.

You may have a problem with your Internet service provider, which is the most typical cause.

Fiber cuts and core outages might cause your Internet to be down for a few minutes or possibly a few days, depending on the severity of the problem.

When I lived in Boston, I had Internet outages lasting more than eight hours on a number of occasions. Workmen cutting through my Internet service provider’s fiber-optic cable were to blame for both incidents.

Another major cause of Internet outages is a breakdown in technology or the failure of a gadget or piece of hardware.

However much you shell out on the newest router technology, there is a good chance that it will eventually fail.

Often, the problem is brief and may be solved by restarting the router, but it can also be long-term and need the router to be replaced. That would need the purchase of a new router.

See also  SmartThings Multipurpose Sensor Battery (How To Replace and More!)

Human error is also a major factor in Internet outages.

Examples of human mistake include not setting up the modem/router equipment properly, loose cables, wrong WiFi passwords, and so on.

When a youngster walks by, it doesn’t take long for him or her to pull out a few cords without your knowledge.

Conclusion

As a result of a loss of Internet connection, your Nanit baby monitor app will indicate a “local view only” status (or your Local Area Network).

It’s important to realize that Internet and the WiFi are not the same thing.

Wireless LAN (WiFi) is a collection of technologies that allow your computer, phone, etc. to connect to your LAN (your router!).

There are hundreds of millions of smaller networks linked to the Internet, on the other hand.

There are occasions when a Wi-Fi connection to the internet is lost yet the WiFi connection remains functioning.

A wonderful feature of the Nanit baby monitor is that you may still use it even if you don’t have an active Internet connection!

The most typical causes of lost connections include problems with your Internet service provider (ISP), problems with your modem/router, and human error.

Try disconnecting or hard resetting your router to recover your Internet connection. If neither option works, you should contact your Internet service provider (ISP) for assistance.

Leave a Comment

Your email address will not be published. Required fields are marked *