Why does my Blu Ray player say no signal?
Try a different HDMI cable. Try a different HDMI input on the TV. If for some reason the player is set to a video resolution too high for the TV it may indicate no signal. Try connecting it to another TV and if you can get to the set up menu check the video resolution and change it.
What is HTTP port disabled?
Re: Samsung Blu-ray player says the HTTP port is disabled When you manually enter a static IP address into the player, you are setting up the player to NOT use DHCP. You can’t just use the same IP address that the router had previously assigned to the player.
Why does my TV say no signal when HDMI is plugged in?
The “no signal error” on a TV is due to using the wrong HDMI cable, a faulty graphics driver or a damaged HDMI port. A “no signal error” on a television can occur because of the following: Faulty chipset.
Why is Blu-Ray not working?
The Blu-ray disc tray may be damaged – If you have an ejectable disc tray, eject your disc and take care to observe any slow opening, wobbles, or misalignment. Try reseating the disc. Blu-ray cables may be loose – A loose connection or incorrect connection will prevent the video from being displayed.
Why is my Sony Blu-Ray player not working?
Make sure the settings of the Blu-ray Disc player is correct. Unplug the power cord of the Blu-ray Disc player from the electrical outlet. Let the player remain without power for one minute. Plug the power cord back into the electrical outlet.
How do I unlock my Samsung DVD player?
Turn the lock off. “Lock Off” will appear in the upper left corner of the TV screen. Note: If LOCK ON displays instead, then your player was not locked to begin with. Enter 4-8-2-7-3 again to unlock it.
Where is eject button on Samsung Blu Ray player?
There is a hole below the bottom chassis. This hole is used to eject the tray manually.
How do I update my Blu Ray player?
Power on the Blu-ray Disc player. If there is a disc in the player, please remove the disc. At the Home Screen menu, use the arrow keys on the remote control to select Setup – Software Update and then press the ENTER button. A New Software Version available message will be prompted.
What does Prot mean on Samsung DVD player?
Posted: 03/16/14. darren, The prot means it goes into protection mode and shuts itself down to prevent any further damage. It is possible that your DVD player has detected a problem in the amplifier section and is shutting down to prevent further damage.
How do I connect my Samsung Blu ray player to the Internet Wired?
Why does my Samsung TV say no signal when HDMI is plugged in?
Generally, a Samsung TV won’t recognize HDMI cable, even after connecting it correctly, if the HDMI is damaged or the resolution from your input is not compatible with the requirements of your Samsung TV. To tell the exact problem, you need to switch your HDMI cable or connect to a different device.
Why is my Samsung TV not recognize HDMI input?
Disconnect and reconnect the HDMI cable. Disconnect the HDMI cable from the back of the TV and the external device. Then reconnect it firmly to the external device first, then connect it to your TV. If it still doesn’t work, try the cable in a different port. Don’t forget to select the new source.
Why is my Samsung TV saying no signal?
The most common reason why a Samsung TV experiences no signal through HDMI is that the HDMI is not connected properly. Unplug the HDMI cable and inspect the cable for any damage. Make sure the ports are free of debris. You can then plug in the cable, making sure to seat it properly.
Why won’t my Samsung Blu-Ray player play blu rays?
There are several reasons a disc may not play in the Blu-ray player. A dirty or scratched disc is the most obvious cause, but an incorrect region code or configuration of your home theater system can be the reason as well. Whether you’re having trouble with 4K or 3D, Blu-ray or DVD, there is a fix.
Why is my Blu-Ray player playing DVDs but not Blu Rays?
If you have DVDs from both, you probably also have a DVD player which plays both. If your Blu-ray player does not, then that DVD player will play a much better picture than none at all. Either the disk is bad, the disk is inserted improperly or the DVD player is not working. Make sure the disk is inserted properly.
Is there a reset button on a Sony Blu-Ray player?
Steps to perform Factory Reset on your Blu-ray Disc? Player or Network Media Player. on the remote control to navigate through the menus, and press the center button to select an option. Under Resetting, select either Reset to Factory Default Settings or Initialize Personal Information.
Do I need to update my Samsung Blu Ray player?
No matter what model of Samsung Blu-ray player you have, it must have the most current firmware installed if you want to enjoy the best movie-watching experience.
How do I update the software on my Samsung DVD player?
How do I unlock my Blu Ray player?
Press and hold the PAUSE or the STOP button on the Blu-ray Disc player for approximately 10 seconds until LOCKED is displayed on the front panel display. NOTE: Depending on the model, you will have to press either the PAUSE button or the STOP button.
Can I connect a DVD player to my Samsung Smart TV?
A DVD Player can be connected to a TV using an HDMI, composite, component, or S-Video cable. Check to see what connections your Samsung TV supports before you purchase a DVD or Blu-ray player. You will then need to select the proper source or “input” on your TV to view the DVD player once it’s connected.
How do you open a Samsung DVD player without a remote?
Originally Answered: How do I turn on my Samsung Blu-ray DVD player without a remote? There should be a power button that will turn it on, and off. Eject button so you can play a disk. However, if it has menus (and most movies do), you may not be able to “get around”.
How long do Blu-Ray players last?
Blu-ray Players: Rest in Peace Sure, families will replace the device after about six years, but they’ll do so with Netflix, HBO Go and Apple TV, not more discs and Blu-ray features. And even if they don’t, they can always just use their PS4s or Xbox Ones.
Should I upgrade my Blu-ray player?
Our opinion is that you should consider upgrading immediately if you are still using a first-gen player. If you haven’t upgraded any of your other components then it may not be as critical for audio quality. Those with newer AV receiver, however, may experience a nice bump in audio capabilities after an upgrade.
How do I reset my Samsung Blu-Ray Player Ht j5500w?
2 With no disc in the player press and hold the Play/Pause button infront of the BD player for about 8 seconds or until “Resetting all settings to default values…” is displayed on your TV screen. The Blu-ray player then powers off and resets.
Why does my Samsung Blu-Ray player keep turning off?
Your home theater system has built in overheating protection. If it gets too hot, it will shut itself down to prevent itself from melting.